Data
| Brand: | Bison |
| Model: | Acrylic sealant Rainproof 300ml White |
| temp.resistance: | -20°C to +75°C |
| Moisture resistance: | Very Good |
| Paintability: | Very Good |
| Filling capacity: | Good |
| UV resistance: | Good |
| Elasticity: | Limited |
| Viscosity: | Approx. 0 mPa.s., Pasty |
| Density: | approx. 1.54 g/cm³ |
| Solids content: | approx. 83 % |
| Shrinkage: | approx. 17 % |
| Max. permissible deformation: | approx. 12.5 % |
| Colour: | White |
| Content: | 300ml |
| Delivery: | 1 piece |
| Ombox in holds: | 12 pieces |
| Appendix: | Declaration of performance.PDF |
Information
Product description
High-quality, easy-to-process, fast rainproof plasto-plastic
acrylic dispersion-based sealant for sealing joints, seams
gaps and cracks. Can be painted over and tightly dimensioned. Indoor and outdoor
Applicable indoors and outdoors.
Field of application
Suitable for sealing low-activity joints, seams and cracks on
door and window frames, window sills, panelling, stairs, skirting boards, walls,
plasterboard, ceilings and transit pipes. Also suitable for sealing cracks
of cracks and fissures in walls. Adheres to brick, (gas) concrete, masonry,
plaster, wood and most other porous substrates. Does not adhere
bitumen, PE, PP, P.T.F.E. and silicones. For sealing in glazing use Bison
Glazing sealant. Not suitable for bitumen, silicones, polyethylene
(PE), polypropylene (PP) and P.T.F.E.
Properties
- Paintable
- Tight-fitting
- Easy to process
- Moisture-resistant
- Excellent adhesion without primer
- Very good sprayability
- Waterproof after complete curing
- UV- and weather-resistant
- Can be used indoors and outdoors
- Permanently elasto-plastic (max. 12.5% elongation)
- Temperature resistant from -20°C to +75°C
Preparation
Processing conditions: Only process at temperatures
between +5°C and +40°C.
Surface requirements: The substrate must be thoroughly dry, clean and dust-,
rust, paint and grease free.
Preliminary treatment surfaces: For better adhesion on porous (strongly
porous substrates, these should first be coated with a diluted
acrylic solution (1 part sealant to 2 parts water). For a good result, tape the edges
of the joint with masking tape. Ensure a minimum joint width
of 6 mm. Up to 12 mm joint width, the joint depth should be 6 mm. For larger
joint widths, the joint depth is half the joint width. Remove masking tape immediately
after smoothing.
Tools: Use the cartridge with Power Pistol. Multi Tool for opening the cartridge and
of the cartridge and smoothing out the sealant.
Processing
Consumption: Contents suitable for approx. 8-15 metres (depending on joint diameter).
of the joint).
Instructions for use:
Process tube with sealant gun. Open the cartridge by cutting off the plastic nipple
cutting off the plastic nipple at the top with a sharp knife up to the thread. Screw on the nozzle
and cut off at an angle at the desired opening. Ensure a minimum
joint width of 6 mm and a maximum of 24 mm. The depth of the joint should be 6
to 9 mm. Spray sealant evenly into the joint and within 5 minutes with
with a moistened putty knife or Bison Multi Tool. The applied
tape immediately after smoothing. After 5 minutes a surface
surface skin.
Stains/Residue: Remove wet stains immediately with water. Cured
residues can only be removed mechanically.
Points of attention: The sealant is paintable after complete curing.
Drying times*
Curing speed: approx. 1 mm/24 hrs.
* Drying times may vary depending on e.g. substrate, applied quantity of product,
moisture content and ambient temperature.
Storage conditions
Minimum 12 months after production. Opened packaging has limited shelf life.
shelf life. Store in tightly closed packaging in a cool, dry and
frost-free place.
Warranty
Only for manufacturing defects.
Right of return
You have a trial period of 14 days. If the product is not to your satisfaction, you may return it to us. The product can only be returned if the outer packaging (seal) is closed.
