Data
Brand: | Bison |
Model: | Montagekit Heavy Duty 425g |
temp.resistance: | -40°C - +100°C |
Water resistance: | Good |
Moisture resistance: | Very good |
Paintability: | Good |
Filling capacity: | Very Good |
Chemical resistance: | Good |
UV resistance: | Very Good |
Mould resistance: | Good |
Elasticity: | Good |
Basic raw material: | SMP polymer |
Viscosity: | approx. Tixotropic |
Solids content: | approx. 100% |
Density: | approx. 1.53 g/cm³ |
Flash point: | K3 (>55°C) |
Shrinkage: | approx. 0 % |
Colour: | White |
Content: | 425g |
Delivery: | 1 piece |
Information
Product description
Universal assembly adhesive with high initial adhesion based on SMP
technology. For fixing heavy materials securely on all substrates and
substrates and joints with high demands. For internal
and external use, filling and permanently elastic.
Field of application
Ideal for mounting all kinds of (construction) materials such as wood, stone
concrete, metal and many plastics on practically any substrate of stone
concrete, wood, metal, plastic, plaster, plasterboard, etc. Also very suitable
for bonding two non-porous materials.
Very suitable for fixing e.g. battens, skirting boards, thresholds,
panelling (wood/plastic), panelling, window sills, ceramic
tiles, sheet material, plasterboard, finishing battens, wall covering boards
panels, insulation material, soft- and hardboard boards, panels, sills
nameplates, house numbers, hooks, cable trays, sockets and
electrical boxes.
Also suitable for mirrors and stone. Not suitable for PE, PP, PTFE and bitumen.
When bonding plastics, always carry out an adhesion test first. The
adhesion to plastic may vary depending on the type and quality of the plastic.
quality of the plastic.
Properties
- High initial tack
- High final strength
- Permanently elastic
- Resistant to all weather influences
- Filling
- Suitable for uneven substrates
- Solvent-free
- SMP technology
Preparation
Processing conditions: Only process at temperatures
between +5°C and +40°C.
Surface requirements: Both parts must be firm, clean, dust- and grease-free.
Use of primer not necessary. Substrate may be slightly moist.
Tools: Canister with sealant gun (e.g. Bison Power Pistol).
Processing. If necessary, use a rubber hammer for tapping.
Processing
Instructions for use:
Before use, open the tube at the top by opening the plastic nipple above
the thread, using a sharp knife. Then attach the nozzle
attach and cut it at an angle to the desired diameter. Cut the
nozzle just above the thread for maximum opening. Glue
evenly, depending on the weight of the material, every 20 to
40 cm in vertical stripes or dots. Always apply adhesive
on corners and along edges. Attach the object with a sliding movement
and press or tap firmly (rubber hammer). Hand-tight
after approx. 30 minutes (the bond is now sufficiently strong for transport or light
load). Load-bearing after approx. 4 hours, depending on the substrate (at least
1 porous material) and the ambient conditions. Corrections are still
possible. After use, immediately close tube tightly.
Stains/Residue: Use white spirit for cleaning tools and
removing wet glue residues. Dried adhesive residues can only be
can only be removed mechanically.
Points of attention: The drying times below are based on the bonding
of at least one porous material and an adhesive layer with a thickness of approx. 1 mm.
When bonding two non-porous materials and/or a thicker adhesive layer,
considerably longer drying times must be expected.
Drying times*
Skin formation time: approx. 10-15 minutes
Hand-holding time: approx. 30 minutes. This may vary depending on
conditions, such as temperature and humidity.
Curing time: approx. 2 mm/24 hours
Drying/hardening time: approx. 4 hours. This may vary depending on the
conditions, such as temperature and humidity.
* Drying times may vary depending on, among other things, substrate, amount of product applied,
moisture content and ambient temperature.
Storage conditions
Minimum 12 months. Opened packaging has limited shelf life. Store well
Keep tightly closed in a dry, cool and frost-free place.
Warranty
Only for manufacturing defects.
Right of return
You have a trial period of 14 days. If the product is not to your satisfaction, you can return it to us. The product can only be returned if the outer packaging (seal) is closed.