Data

Information

Product description
Universal assembly adhesive and sealant based on unique SMP technology,
with rapid final strength build-up. For bonding, mounting and sealing of
virtually all (building) materials on virtually all substrates (both smooth
porous and non-porous substrates). Can be used indoors and outdoors. Super
fast. Extra strong.

Area of application
Adhesives: e.g. glass, stone, natural stone, concrete, plaster, many synthetic materials,
wood, chipboard, Trespa®, iron, aluminium, zinc, steel, stainless steel and other metals,
ceramic tiles, cork and mirrors.
Fitting: including skirting boards, mouldings, battens, window sills,
thresholds, fascia boards, sheet material, insulation material, plasterboard,
polystyrene ornaments and mouldings.
Sealing: including skirting boards, (plastic) frames, stair treads, window sills,
thresholds and plasterboards. Also suitable for sealing cracks
in walls and ceilings. Not suitable for PE, PP, PTFE and bitumen. When
always first conduct an adhesion test. The adhesion
may vary depending on the type of plastic and the quality of the plastic.
the plastic.

Properties
- Super-fast final strength build-up
- Very high final strength
- Permanently elastic
- Can be used indoors and outdoors
- Paintable (test beforehand)
- Good filling capacity
- Temperature resistant from -40°C to +100°C
- UV, water and weather resistant
- 100% adhesive (non-shrink)
- Adheres to slightly damp substrates
- Solvent-free
- Excellent adhesion without primer
- Acid-free, odourless

Preparation
Processing conditions: Only process at temperatures
between +5°C and +40°C.
Surface requirements: Both parts must be firm, clean, dust- and grease-free.
Use of primer not necessary. Substrate may be slightly moist.
Tools: Canister with sealant gun (e.g. Bison Power Pistol).
Processing. If necessary, use a rubber hammer for tapping.

Processing
Consumption: For dotwise bonding: 5-8 m²/kg. Striping: 1 tube yields approx.
8-15 metres of adhesive (depending on diameter cut-off nozzle).
Instructions for use:
Before use, open the tube at the top by opening the plastic nipple above
the thread, using a sharp knife. Then attach the nozzle
and cut it at an angle to the desired diameter. Gluing and
fitting: Cut the nozzle to a diameter of at least 0.5 cm.
Sealing: Cut the nozzle at an angle depending on the desired joint width.
off. Gluing and fitting: Apply sealant in stripes or dots (every 10-40 cm)
plus always at corner points and along the edges of board material. Material
in the right place within 10 minutes and press firmly or lightly
tap with a rubber hammer. If necessary, clamp or fix heavy materials for 4 hours.
or fixate. Hand strength after 30 minutes (the connection is now sufficiently strong for
transport or light loading); maximum final strength after approx. 4 hours, depending on substrate and ambient conditions.
the substrate and ambient conditions.
Sealing: Apply sealant evenly to the bottom of the joint and
smooth out within 10 minutes with a moist (soapy water without lemon)
putty knife, sealant spreader or finger. Vertical joints from bottom to top
smoothen vertical joints from bottom to top. Complete curing after a few days (depending on layer thickness).
When repainting with alkyd paints, the paint may dry more slowly.
dry.
Stains/Residue: Use white spirit for cleaning tools and
removing wet glue residues. Dried glue residues can only be
mechanically removable.
Points of attention: The drying times below are based on the bonding
of at least one porous material and an adhesive layer with a thickness of approx. 1 mm.
When bonding two non-porous materials and/or a thicker adhesive layer,
considerably longer drying times must be taken into account

Only for manufacturing defects.

Right of return

You have a 14-day trial period. If the product is not to your satisfaction, you can return it to us. The product can only be returned if the outer packaging (seal) is closed.