Data
| Brand: | Bison |
| Model: | Wood glue Topspeed |
| temp.resistance: | -20°C to +60°C |
| Moisture resistance: | Good |
| Water resistance: | Limited |
| Paintability: | Good |
| Filling capacity: | Not |
| Basic raw material: | Polyvinyl acetate dispersion |
| Viscosity: | Approx. 12,000 mPa.s., Liquid |
| Solids content: | approx. 60% |
| Density: | approx. 1.1 g/cm³ |
| White point: | approx. 6 °C |
| pH value: | approx. 4.5 |
| Flash point: | K3 (>55°C) |
| Colour: | White (Transparent after drying) |
| Content: | 75g |
| Delivery: | 1 piece |
Information
Product description
High-quality, fast (drying time 4 minutes), moisture-resistant (EN 204 D2) white wood glue for indoor use. Transparent drying. Stronger than wood. For gluing and laminating almost all hard, soft and exotic types of wood.
Field of application
For moisture-resistant bonding and laminating of practically all hard, soft and exotic types of wood.
and exotic types of wood. Applicable for well-fitting, non-load-bearing
wood constructions e.g. by finger jointing, dovetailing, mortise and tenon joints, dowels and springs.
joints, dowels and springs. Suitable for interior applications such as doors
and furniture in, for example, living rooms and offices. For surface bonding
of wood, soft- and hardboard, chipboard, plywood, MDF, paper, cardboard and
board. Also for laminating veneers and hard plastic sheet (HPL; Formica,
Duropal, Resopal) on wooden substrates. EN 204 D2: Indoor areas, where occasionally
occasionally an increased relative humidity of the air for a short period of time
occurs, where the wood moisture content remains below 18%.
Properties
- Very fast (4 minutes)
- Stronger than wood
- Transparent drying
- Ideal for interior applications (EN 204 D2)
- Paintable
- Solvent-free
Preparation
Processing conditions: The temperature of the environment, the
adhesive and the materials to be bonded should not be lower than +5°C. Relative
humidity of maximum 65%. Wood humidity between 8%
and 12%.
Surface requirements: The surfaces to be glued must be clean, dry and
be dust-free. Ensure a well-fitting joint.
Pre-treatment surfaces: Degrease oily wood with
'Thinner for Bison Kit®' or Thinner.
Tools: Fine-toothed glue comb (1 mm), brush or roller, clamp or press.
Processing
Dilute: If necessary, dilute with water to original viscosity.
viscosity.
Consumption: 2-4 m²/kg, applied on both sides, depending on the nature of the
materials.
Instructions for use:
Apply the adhesive with a brush or other tool evenly, thinly to one or
both parts. Leave to penetrate for a few minutes, then bond the parts together and
and press for 4-15 min. The required
press pressure is 2-5 kg/cm².
Pressing pressure: 5-10 kg/cm².
Pressing time: 4-15 minutes (more in case of tension)
Open time: 6 minutes
Stains/Residue: Remove wet adhesive residues immediately with water. Dried
adhesive residues can only be removed mechanically.
Tips: For water-resistant bonding, use Bison Wood Max® (EN 204
D4).
Storage conditions
Minimum 24 months after production. Opened packaging has a limited
shelf life. Store tightly closed in a dry, cool and frost-free place.
Warranty
Only for manufacturing defects.
Right of return
You have a 14-day trial period. If the product is not to your satisfaction, you can return it to us. The product can only be returned if the outer packaging (seal) is closed.
